Showing 25–36 of 168 results

Show sidebar
Close

200 Amp T Fuse

$62.90

200 Amp T Fuse

Add to cart
tristar digital remote meter
Close

TriStar Remote Digital Meter

$188.06

A Remote Display for all TriStar Charge Controllers

The TriStar Remote Meter includes 30 meters of cable for mounting the meter away from the controller.

Five year warranty.

The TS-RM-2 info sheet can be found under “Manuals” on our site.

Add to cart
tristar ts-m 2
Close

TriStar Digital Meter

$136.66

Display Cover for TriStar Charge Controllers.

The TriStar Digital Meter mounts to the front of the charge controller and provides system and controller information, data logging, bar graphs and choice of 5 languages.

Five year warranty.

The TS-M-2 info sheet can be found under “Manuals” on our site.

Add to cart
SaleHot
magnum inverter
Close

MS4448PAE Magnum Inverter

$2,943.04 $2,523.15

Why buy Magnum?

Experience:

Magnum Energy is a leading manufacturer of premium inverter chargers, with over 70 years of combined inverter design and manufacturing experience.

Reliability:

Magnum inverters are manufactured in Everett, Washington, and St. Paul, Minnesota, U.S.A. 

Quality: 

You get what you pay for. Simple. These are not cheap, made in China products.

4400 watt 48V 120/240 Inverter/Charger

The MS-PAE Series Inverter/Charger from Magnum Energy is a pure sine wave inverter designed specifically for the most demanding renewable energy applications. The unique design of the MS-PAE Series provides two 120VAC output lines that are 180° out-of-phase with each other, so that the combination of the L1 and L2 lines total 240VAC and the voltage between either L1 or L2 and neutral is 120VAC, eliminating the need to purchase two units and stack them together to get 240 volts.

When the power requirements of the system are beyond the capacity of a single MS-PAE Series inverter or the system is expanded as more loads are added, up to four MS-PAE Series inverters can be connected together in a parallel configuration. When connecting inverters in parallel, the overall inverter power and surge capacity is increased to power a large single load or more smaller loads.

Available in 4000 (24 volts) and 4400 (48 volts) watt models, the MS-PAE Series inverters are powerful, easy-to-use and ETL listed to the stringent requirements of UL 1741 and CSA C22.2 No. 107.1-01 for Renewable Energy installations.

Two year manufacturers warranty.

 

 

 

Add to cart
Sale
magnum inverter
Close

Magnum Inverter MS4024

$2,734.24 $2,344.14

4000 watt 24V Inverter/Charger

The MS Series Inverter/Charger from Magnum Energy is a pure sine wave inverter designed specifically for the most demanding mobile and off grid applications. The MS series is powerful, easy-to-use, and best of all, cost effective. A PFC (Power Factor Corrected) charger is built into all Magnum Energy’s inverter/chargers. It uses less energy from a generator than a standard charger – using 25-30% less AC current than standard chargers.

The MS4024 spec sheet can be found under “Manuals” on our site.

Two year manufacturers warranty.

Add to cart
magnum energy battery monitor kit
Close

Magnum Energy Battery Monitor Kit

$228.64

The Battery Monitor Kit from Magnum Energy gives you a “fuel gauge” type of meter for your battery bank. It monitors the battery bank and reports the percentage state of charge, real time amps, voltage, amp-hours in/out, and the minimum/maximum DC volts.

The Battery Monitor Kit includes the sense module, sense and communication cables, and a 500 amp shunt.

The ME-BMK requires a Magnum Inverter with a “Network” port and a ME-RC50 remote with revision 2.0 or higher.

The ME-BMK info sheet can be found under “Manuals” on our site.

Interested in Magnum Energy Inverters? Click here: Magnum Energy Inverters

Add to cart
mc4 cable
Close

MC4 Extension 100ft

$96.56

MC4 Extension 100ft cables are typically used to run from the solar panel(s) to the charge controller or combiner box.

Features:

  • snap together, multi-contact hard plastic connectors on each end
  • cable comes with a male connector on one end and a female connector on the other end.
  • Made with black #10 AWG USE-2 sunlight resistant cable.
Add to cart
mc4 cable
Close

MC4 Extension 50ft

$53.56

MC4 Extension 50ft cables are typically used to run from the solar panel(s) to the charge controller or combiner box.

Features:

  • snap together, multi-contact hard plastic connectors on each end
  • cable comes with a male connector on one end and a female connector on the other end.
  • Made with black #10 AWG USE-2 sunlight resistant cable.
Add to cart
Victron Energy Phoenix Charger 12 Volt 30 Amp (2+1) 120-240V
Close

Victron Energy Phoenix Charger 12/30 (2+1) 120-240V

$630.96

Victron Energy Phoenix Charger 12/30 (2+1) 120-240V SKU : PCH012030001

  • Input voltage range (V AC): 90-265
  • Input voltage range (V DC): 90-400
  • Frequency (Hz): 45-65
  • Power factor: 1
  • Charge voltage ‘absorption’ (V DC): 14,4
  • Charge voltage ‘float’ (V DC): 13,8
  • Storage mode (V DC): 13,2
  • Charge current house batt. (A) (2): 30
  • Charge current starter batt. (A): 4
  • Charge characteristic: 4 stage adaptive
  • Battery capacity (Ah): 100-400
  • Temperature sensor √
  • Can be used as power supply √
  • Forced cooling √
  • Protection (1): a,b,c,d
  • Operating temp. range: -20 to 60°C (0 – 140°F)
  • Humidity (non-condensing): max 95%

ENCLOSURE

  • Material & Colour: aluminium (blue RAL 5012)
  • Battery-connection: M6 studs
  • AC-connection: screw-clamp 4 mm² (AWG 11)
  • Protection category: IP 21
  • Weight kg (lbs): 3,8 (8)
  • Dimensions (hxwxd in mm and inches): 350x200x108 mm (13.8×7.9×4.3 inch)

STANDARDS

  • Safety: EN 60335-1, EN 60335-2-29
  • Emission Immunity: EN 55014-1, EN 61000-3-2,
  • Automotive Directive: EN 55014-2, EN 61000-3-3
  • Vibration: IEC68-2-6:10-150Hz/1.0G

Adaptive 4-stage charge characteristic: bulk – absorption – float – storage
The Phoenix Charger features a microprocessor controlled ‘adaptive’ battery management system that can be preset to suit different types of batteries. The ‘adaptive’ feature will automatically optimize the process relative to the way the battery is being used.

The right amount of charge: variable absorption time
When only shallow discharges occur (a yacht connected to shore power for example) the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge, the absorption time is automatically increased to make sure that the battery is completely recharged.

Preventing damage due to excessive gassing: the BatterySafe mode (see fig. 2 below)
If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the victron energy phoenix charger will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached (see the charge curve between 14,4 V and 15,0 V in fig. 2 below).

Less maintenance and aging when the battery is not in use: the Storage mode (see fig. 1 & 2 below)
The storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode, float voltage is reduced to 2,2 V/cell (13,2 V for 12 V battery) to minimize gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.

To increase battery life: temperature compensation
Every Victron Energy Phoenix Charger comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed batteries and/or when important fluctuations of battery temperature are expected.

Battery voltage sense
In order to compensate for voltage loss due to cable resistance, Phoenix Chargers are provided with a voltage sense facility so that the battery always receives the correct charge voltage. Universal 90-265 V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation). The chargers will accept a 90-400 V DC supply.

Computer interface
Every Victron Energy Phoenix Charger is ready to communicate with a computer through its RS-485 data port. Together with our VEConfigure software, which can be downloaded free of charge from our website www.victronenergy.com and the data link MK2-USB (see accessories), all parameters of the chargers can be customized.

Add to cart
Victron Energy Phoenix Charger 12 Volt 50 Amp (2+1) 120-240V
Close

Victron Energy Phoenix Charger 12/50 (2+1) 120-240V

$843.48

Victron Energy Phoenix Charger 12/50 (2+1) 120-240V SKU : PCH012050001

  • Input voltage range (V AC): 90-265
  • Input voltage range (V DC): 90-400
  • Frequency (Hz): 45-65
  • Power factor: 1
  • Charge voltage ‘absorption’ (V DC): 14,4
  • Charge voltage ‘float’ (V DC): 13,8
  • Storage mode (V DC): 13,2
  • Charge current house batt. (A) (2): 50
  • Charge current starter batt. (A): 4
  • Charge characteristic: 4 stage adaptive
  • Battery capacity (Ah): 200-800
  • Temperature sensor √
  • Can be used as power supply √
  • Forced cooling √
  • Protection (1): a,b,c,d
  • Operating temp. range: -20 to 60°C (0 – 140°F)
  • Humidity (non-condensing): max 95%

ENCLOSURE

  • Material & Colour: aluminium (blue RAL 5012)
  • Battery-connection: M6 studs
  • AC-connection: screw-clamp 4 mm² (AWG 11)
  • Protection category: IP 21
  • Weight kg (lbs): 3,8 (8)
  • Dimensions (hxwxd in mm and inches): 350x200x108 mm (13.8×7.9×4.3 inch)

STANDARDS

  • Safety: EN 60335-1, EN 60335-2-29
  • Emission Immunity: EN 55014-1, EN 61000-3-2,
  • Automotive Directive: EN 55014-2, EN 61000-3-3
  • Vibration: IEC68-2-6:10-150Hz/1.0G

Adaptive 4-stage charge characteristic: bulk – absorption – float – storage
The Phoenix Charger features a microprocessor controlled ‘adaptive’ battery management system that can be preset to suit different types of batteries. The ‘adaptive’ feature will automatically optimize the process relative to the way the battery is being used.

The right amount of charge: variable absorption time
When only shallow discharges occur (a yacht connected to shore power for example) the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge, the absorption time is automatically increased to make sure that the battery is completely recharged.

Preventing damage due to excessive gassing: the BatterySafe mode (see fig. 2 below)
If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the victron energy phoenix charger will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached (see the charge curve between 14,4 V and 15,0 V in fig. 2 below).

Less maintenance and aging when the battery is not in use: the Storage mode (see fig. 1 & 2 below)
The storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode, float voltage is reduced to 2,2 V/cell (13,2 V for 12 V battery) to minimize gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.

To increase battery life: temperature compensation
Every Victron Energy Phoenix Charger comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed batteries and/or when important fluctuations of battery temperature are expected.

Battery voltage sense
In order to compensate for voltage loss due to cable resistance, Phoenix Chargers are provided with a voltage sense facility so that the battery always receives the correct charge voltage. Universal 90-265 V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation). The chargers will accept a 90-400 V DC supply.

Computer interface
Every Victron Energy Phoenix Charger is ready to communicate with a computer through its RS-485 data port. Together with our VEConfigure software, which can be downloaded free of charge from our website www.victronenergy.com and the data link MK2-USB (see accessories), all parameters of the chargers can be customized.

Add to cart
Victron Energy Phoenix Charger 24Volt 16Amp (2+1) 120-240V
Close

Victron Energy Phoenix Charger 24/16 (2+1) 120-240V

$630.96

Victron Energy Phoenix Charger 24/16 (2+1) 120-240V SKU : PCH024016001

  • Input voltage range (V AC): 90-265
  • Input voltage range (V DC): 90-400
  • Frequency (Hz): 45-65
  • Power factor: 1
  • Charge voltage ‘absorption’ (V DC): 28,8
  • Charge voltage ‘float’ (V DC): 27,6
  • Storage mode (V DC): 26,4
  • Charge current house batt. (A) (2): 16
  • Charge current starter batt. (A): 4
  • Charge characteristic: 4 stage adaptive
  • Battery capacity (Ah): 100-200
  • Temperature sensor √
  • Can be used as power supply √
  • Forced cooling √
  • Protection (1): a,b,c,d
  • Operating temp. range: -20 to 60°C (0 – 140°F)
  • Humidity (non-condensing): max 95%

ENCLOSURE

  • Material & Colour: aluminium (blue RAL 5012)
  • Battery-connection: M6 studs
  • AC-connection: screw-clamp 4 mm² (AWG 11)
  • Protection category: IP 21
  • Weight kg (lbs): 3,8 (8)
  • Dimensions (hxwxd in mm and inches): 350x200x108 mm (13.8×7.9×4.3 inch)

STANDARDS

  • Safety: EN 60335-1, EN 60335-2-29
  • Emission Immunity: EN 55014-1, EN 61000-3-2,
  • Automotive Directive: EN 55014-2, EN 61000-3-3
  • Vibration: IEC68-2-6:10-150Hz/1.0G

Adaptive 4-stage charge characteristic: bulk – absorption – float – storage
The Phoenix Charger features a microprocessor controlled ‘adaptive’ battery management system that can be preset to suit different types of batteries. The ‘adaptive’ feature will automatically optimize the process relative to the way the battery is being used.

The right amount of charge: variable absorption time
When only shallow discharges occur (a yacht connected to shore power for example) the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge, the absorption time is automatically increased to make sure that the battery is completely recharged.

Preventing damage due to excessive gassing: the BatterySafe mode (see fig. 2 below)
If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the victron energy phoenix charger will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached (see the charge curve between 14,4 V and 15,0 V in fig. 2 below).

Less maintenance and aging when the battery is not in use: the Storage mode (see fig. 1 & 2 below)
The storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode, float voltage is reduced to 2,2 V/cell (13,2 V for 12 V battery) to minimize gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.

To increase battery life: temperature compensation
Every Victron Energy Phoenix Charger comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed batteries and/or when important fluctuations of battery temperature are expected.

Battery voltage sense
In order to compensate for voltage loss due to cable resistance, Phoenix Chargers are provided with a voltage sense facility so that the battery always receives the correct charge voltage. Universal 90-265 V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation). The chargers will accept a 90-400 V DC supply.

Computer interface
Every Victron Energy Phoenix Charger is ready to communicate with a computer through its RS-485 data port. Together with our VEConfigure software, which can be downloaded free of charge from our website www.victronenergy.com and the data link MK2-USB (see accessories), all parameters of the chargers can be customized.

Add to cart
Victron Energy Phoenix Charger 24V 25A (2+1) 120-240V
Close

Victron Energy Phoenix Charger 24/25 (2+1) 120-240V

$843.48

Victron Energy Phoenix Charger 24/25 (2+1) 120-240V SKU : PCH024025001

  • Input voltage range (V AC): 90-265
  • Input voltage range (V DC): 90-400
  • Frequency (Hz): 45-65
  • Power factor: 1
  • Charge voltage ‘absorption’ (V DC): 28,8
  • Charge voltage ‘float’ (V DC): 27,6
  • Storage mode (V DC): 26,4
  • Charge current house batt. (A) (2): 25
  • Charge current starter batt. (A): 4
  • Charge characteristic: 4 stage adaptive
  • Battery capacity (Ah): 100-400
  • Temperature sensor √
  • Can be used as power supply √
  • Forced cooling √
  • Protection (1): a,b,c,d
  • Operating temp. range: -20 to 60°C (0 – 140°F)
  • Humidity (non-condensing): max 95%

ENCLOSURE

  • Material & Colour: aluminium (blue RAL 5012)
  • Battery-connection: M6 studs
  • AC-connection: screw-clamp 4 mm² (AWG 11)
  • Protection category: IP 21
  • Weight kg (lbs): 3,8 (8)
  • Dimensions (hxwxd in mm and inches): 350x200x108 mm (13.8×7.9×4.3 inch)

STANDARDS

  • Safety: EN 60335-1, EN 60335-2-29
  • Emission Immunity: EN 55014-1, EN 61000-3-2,
  • Automotive Directive: EN 55014-2, EN 61000-3-3
  • Vibration: IEC68-2-6:10-150Hz/1.0G

Adaptive 4-stage charge characteristic: bulk – absorption – float – storage
The Phoenix Charger features a microprocessor controlled ‘adaptive’ battery management system that can be preset to suit different types of batteries. The ‘adaptive’ feature will automatically optimize the process relative to the way the battery is being used.

The right amount of charge: variable absorption time
When only shallow discharges occur (a yacht connected to shore power for example) the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge, the absorption time is automatically increased to make sure that the battery is completely recharged.

Preventing damage due to excessive gassing: the BatterySafe mode (see fig. 2 below)
If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the victron energy phoenix charger will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached (see the charge curve between 14,4 V and 15,0 V in fig. 2 below).

Less maintenance and aging when the battery is not in use: the Storage mode (see fig. 1 & 2 below)
The storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode, float voltage is reduced to 2,2 V/cell (13,2 V for 12 V battery) to minimize gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.

To increase battery life: temperature compensation
Every Victron Energy Phoenix Charger comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed batteries and/or when important fluctuations of battery temperature are expected.

Battery voltage sense
In order to compensate for voltage loss due to cable resistance, Phoenix Chargers are provided with a voltage sense facility so that the battery always receives the correct charge voltage. Universal 90-265 V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation). The chargers will accept a 90-400 V DC supply.

Computer interface
Every Victron Energy Phoenix Charger is ready to communicate with a computer through its RS-485 data port. Together with our VEConfigure software, which can be downloaded free of charge from our website www.victronenergy.com and the data link MK2-USB (see accessories), all parameters of the chargers can be customized.

Add to cart