Showing 37–48 of 168 results

Show sidebar
Victron Energy Quattro 12/5000/220-100/100 120V VE.Bus
Close

Victron Energy Quattro 12/5000/220-100/100 120V VE.Bus

$4,493.87

Victron Energy QUA125021100 Quattro 12/5000/220-100/100 120V VE.Bus

  • PowerControl / PowerAssist Yes
  • Integrated Transfer switch Yes
  • AC inputs (2x) Input voltage range: 90-140 VAC Input frequency: 45 – 65 Hz Power factor: 1
  • Maximum feed through current 2x 100 A

INVERTER

  • Input voltage range 9,5 – 17 V, 19 – 33V, 38 – 66 V
  • Output (1):  Output voltage: 120 VAC ± 2% and Frequency: 60 Hz ± 0,1%
  • Cont. output power at 25°C (3) 5000 VA
  • Cont. output power at 25°C 4000 W
  • Cont. output power at 40°C 3700 W
  • Cont. output power at 65°C 3000 W
  • Peak power 10000 W
  • Maximum efficiency 94 %
  • Zero load power 30 W
  • Zero load power in AES mode 25 W
  • Zero load power in Search mode 10 W

CHARGER

  • Charge voltage ‘absorption’ (V DC) 14,4 V
  • Charge voltage ‘float’ (V DC) 13,8 V
  • Storage mode (V DC) 13,2 V
  • Charge current house battery (A) (4) 2o0 A
  • Charge current starter battery (A) 4 A (12V and 24V models only)
  • Battery temperature sensor Yes

GENERAL

  • Auxiliary output (5) 50 A
  • Programmable relay (6) 3x
  • Protection (2) a-g
  • VE.Bus communication port for parallel, split phase, and three phase operation, remote monitoring and system integration
  • General purpose com. port 2x
  • Remote on-off Yes
  • Common Characteristics operating temp.: -40 to +65˚C, Humidity (non-condensing): max. 95%

ENCLOSURE

  • Common Characteristics: Material & Colour aluminium (blue RAL 5012) Protection category: IP 21
  • Battery-connection four M8 bolts (2 plus and 2 minus connections)
  • 230 V AC-connection Bolts M6
  • Weight (kg): 75lb, 34kg
  • Dimensions (hxwxd) : 18,5 x 14,0 x 11,2 inch ,  470 x 350 x 280 mm

STANDARDS

  • Safety EN-IEC 60335-1, EN-IEC 60335-2-29, EN-IEC 62109-1
  • Emission, Immunity EN 55014-1, EN 55014-2, EN-IEC 61000-3-2, EN-IEC 61000-3-3, IEC 61000-6-1, IEC 61000-6-2, IEC 61000-6-3
  • Road vehicles 12V and 24V models: ECE R10-5

Two AC inputs with integrated transfer switch
The Quattro can be connected to two independent AC sources, for example, the public grid and a generator, or two generators. The Quattro will automatically connect to the active source.

Two AC Outputs
The main output has no-break functionality. The Quattro takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is life only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, like a water heater, for example, can be connected to this output.

Virtually unlimited power thanks to parallel operation
Up to 6 Quattro units can operate in parallel. Six units 48/10000/140, for example, will provide 48kW / 60kVA output power and 840 Amps charging capacity.

Three phase capability
Three units can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected to provide 144kW / 180kVA inverter power and more than 2500A charging capacity.

PowerControl – Dealing with limited generator, shoreside or grid power
The Quattro is a very powerful battery charger. It will, therefore, draw a lot of current from the generator or shore side supply (16A per 5kVA Quattro at 230VAC). A current limit can be set on each AC input. The Quattro will then take account of other AC loads and use whatever is spare for charging, thus preventing the generator or mains supply from being overloaded.

PowerAssist – Boosting shore or generator power
This feature takes the principle of PowerControl to a further dimension allowing the Quattro to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the Quattro will make sure that insufficient mains or generator power are immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.

Solar energy: AC power available even during a grid failure
The Quattro can be used in off grid as well as grid-connected PV and other alternative energy systems. Loss of mains detection software is available.

System configuring

  • In case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes
    with a DIP switch setting procedure.
  • Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System
    Configurator software.
  • Off-grid, grid interactive, and self-consumption applications, involving grid-tie inverters and/or MPPT Solar
    Chargers can be configured with Assistants (dedicated software for specific applications).

On-site Monitoring and control
Several options are available: Battery Monitor, Multi Control Panel, Color Control GX or other GX devices, smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232).

Remote Monitoring and control
Color Control GX or other GX devices. Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge.

Remote configuring
When connected to the Ethernet, systems with a Color Control GX or other GX device can be accessed and settings can be changed remotely.

Add to cart
Victron Energy Quattro 24/5000/120-100/100 120V VE.Bus
Close

Victron Energy Quattro 24/5000/120-100/100 120V VE.Bus

$3,756.78

Victron Energy QUA245023110 Quattro 24/5000/120-100/100 120V VE.Bus

  • PowerControl / PowerAssist Yes
  • Integrated Transfer switch Yes
  • AC inputs (2x) Input voltage range: 90-140 VAC Input frequency: 45 – 65 Hz Power factor: 1
  • Maximum feed through current 2x 100 A

INVERTER

  • Input voltage range 9,5 – 17 V, 19 – 33V, 38 – 66 V
  • Output (1):  Output voltage: 120 VAC ± 2% and Frequency: 60 Hz ± 0,1%
  • Cont. output power at 25°C (3) 5000 VA
  • Cont. output power at 25°C 4000 W
  • Cont. output power at 40°C 3700 W
  • Cont. output power at 65°C 3000 W
  • Peak power 10000 W
  • Maximum efficiency 94 %
  • Zero load power 30 W
  • Zero load power in AES mode 25 W
  • Zero load power in Search mode 10 W

CHARGER

  • Charge voltage ‘absorption’ (V DC) 28,8V
  • Charge voltage ‘float’ (V DC) 27,6V
  • Storage mode (V DC) 26,4 V
  • Charge current house battery (A) (4) 120 A
  • Charge current starter battery (A) 4 A (12V and 24V models only)
  • Battery temperature sensor Yes

GENERAL

  • Auxiliary output (5) 50 A
  • Programmable relay (6) 3x
  • Protection (2) a-g
  • VE.Bus communication port for parallel, split phase, and three phase operation, remote monitoring and system integration
  • General purpose com. port 2x
  • Remote on-off Yes
  • Common Characteristics operating temp.: -40 to +65˚C, Humidity (non-condensing): max. 95%

ENCLOSURE

  • Common Characteristics: Material & Colour aluminium (blue RAL 5012) Protection category: IP 21
  • Battery-connection four M8 bolts (2 plus and 2 minus connections)
  • 230 V AC-connection Bolts M6
  • Weight (kg): 66 lb, 30kg
  • Dimensions (hxwxd) : 17,5 x 13,0 x 9,6 inch ,  444 x 328 x 240 mm

STANDARDS

  • Safety EN-IEC 60335-1, EN-IEC 60335-2-29, EN-IEC 62109-1
  • Emission, Immunity EN 55014-1, EN 55014-2, EN-IEC 61000-3-2, EN-IEC 61000-3-3, IEC 61000-6-1, IEC 61000-6-2, IEC 61000-6-3
  • Road vehicles 12V and 24V models: ECE R10-5

Two AC inputs with integrated transfer switch
The Quattro can be connected to two independent AC sources, for example, the public grid and a generator, or two generators. The Quattro will automatically connect to the active source.

Two AC Outputs
The main output has no-break functionality. The Quattro takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is life only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, like a water heater, for example, can be connected to this output.

Virtually unlimited power thanks to parallel operation
Up to 6 Quattro units can operate in parallel. Six units 48/10000/140, for example, will provide 48kW / 60kVA output power and 840 Amps charging capacity.

Three phase capability
Three units can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected to provide 144kW / 180kVA inverter power and more than 2500A charging capacity.

PowerControl – Dealing with limited generator, shoreside or grid power
The Quattro is a very powerful battery charger. It will, therefore, draw a lot of current from the generator or shore side supply (16A per 5kVA Quattro at 230VAC). A current limit can be set on each AC input. The Quattro will then take account of other AC loads and use whatever is spare for charging, thus preventing the generator or mains supply from being overloaded.

PowerAssist – Boosting shore or generator power
This feature takes the principle of PowerControl to a further dimension allowing the Quattro to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the Quattro will make sure that insufficient mains or generator power are immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.

Solar energy: AC power available even during a grid failure
The Quattro can be used in off grid as well as grid-connected PV and other alternative energy systems. Loss of mains detection software is available.

System configuring

  • In case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes
    with a DIP switch setting procedure.
  • Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System
    Configurator software.
  • Off-grid, grid interactive, and self-consumption applications, involving grid-tie inverters and/or MPPT Solar
    Chargers can be configured with Assistants (dedicated software for specific applications).

On-site Monitoring and control
Several options are available: Battery Monitor, Multi Control Panel, Color Control GX or other GX devices, smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232).

Remote Monitoring and control
Color Control GX or other GX devices. Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge.

Remote configuring
When connected to the Ethernet, systems with a Color Control GX or other GX device can be accessed and settings can be changed remotely.

Add to cart
Victron Energy Quattro 48/3000/35-50/50 120V VE.Bus
Close

Victron Energy Quattro 48/3000/35-50/50 120V VE.Bus

$2,466.88

Victron Energy QUA483021100 Quattro 48/3000/35-50/50 120V VE.Bus

  • PowerControl / PowerAssist Yes
  • Integrated Transfer switch Yes
  • AC inputs (2x) Input voltage range: 90-140 VAC Input frequency: 45 – 65 Hz Power factor: 1
  • Maximum feed through current 2x 50 A

INVERTER

  • Input voltage range 9,5 – 17 V, 19 – 33V, 38 – 66 V
  • Output (1):  Output voltage: 120 VAC ± 2% and Frequency: 60 Hz ± 0,1%
  • Cont. output power at 25°C (3) 3000 VA
  • Cont. output power at 25°C 2400 W
  • Cont. output power at 40°C 2200 W
  • Cont. output power at 65°C 1700 W
  • Peak power 6000 W
  • Maximum efficiency 94 %
  • Zero load power 25 W
  • Zero load power in AES mode 20 W
  • Zero load power in Search mode 12 W

CHARGER

  • Charge voltage ‘absorption’ (V DC) 57,6 V
  • Charge voltage ‘float’ (V DC) 55,2 V
  • Storage mode (V DC) 52,8 V
  • Charge current house battery (A) (4) 35 A
  • Charge current starter battery (A) 4 A (12V and 24V models only)
  • Battery temperature sensor Yes

GENERAL

  • Auxiliary output (5) 32 A
  • Programmable relay (6) 3x
  • Protection (2) a-g
  • VE.Bus communication port for parallel, split phase, and three phase operation, remote monitoring and system integration
  • General purpose com. port 2x
  • Remote on-off Yes
  • Common Characteristics operating temp.: -40 to +65˚C, Humidity (non-condensing): max. 95%

ENCLOSURE

  • Common Characteristics: Material & Colour aluminium (blue RAL 5012) Protection category: IP 21
  • Battery-connection four M8 bolts (2 plus and 2 minus connections)
  • 230 V AC-connection Screw terminals 13 mm2 (6 AWG)
  • Weight (kg): 42 lb, 19 kg
  • Dimensions (hxwxd) : 14.3 x 10.2 x 8.6 inch,  362 x 258 x 218 mm

STANDARDS

  • Safety EN-IEC 60335-1, EN-IEC 60335-2-29, EN-IEC 62109-1
  • Emission, Immunity EN 55014-1, EN 55014-2, EN-IEC 61000-3-2, EN-IEC 61000-3-3, IEC 61000-6-1, IEC 61000-6-2, IEC 61000-6-3
  • Road vehicles 12V and 24V models: ECE R10-5

Two AC inputs with integrated transfer switch
The Quattro can be connected to two independent AC sources, for example, the public grid and a generator, or two generators. The Quattro will automatically connect to the active source.

Two AC Outputs
The main output has no-break functionality. The Quattro takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is life only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, like a water heater, for example, can be connected to this output.

Virtually unlimited power thanks to parallel operation
Up to 6 Quattro units can operate in parallel. Six units 48/10000/140, for example, will provide 48kW / 60kVA output power and 840 Amps charging capacity.

Three phase capability
Three units can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected to provide 144kW / 180kVA inverter power and more than 2500A charging capacity.

PowerControl – Dealing with limited generator, shoreside or grid power
The Quattro is a very powerful battery charger. It will, therefore, draw a lot of current from the generator or shore side supply (16A per 5kVA Quattro at 230VAC). A current limit can be set on each AC input. The Quattro will then take account of other AC loads and use whatever is spare for charging, thus preventing the generator or mains supply from being overloaded.

PowerAssist – Boosting shore or generator power
This feature takes the principle of PowerControl to a further dimension allowing the Quattro to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the Quattro will make sure that insufficient mains or generator power are immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.

Solar energy: AC power available even during a grid failure
The Quattro can be used in off grid as well as grid-connected PV and other alternative energy systems. Loss of mains detection software is available.

System configuring

  • In case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes
    with a DIP switch setting procedure.
  • Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System
    Configurator software.
  • Off-grid, grid interactive, and self-consumption applications, involving grid-tie inverters and/or MPPT Solar
    Chargers can be configured with Assistants (dedicated software for specific applications).

On-site Monitoring and control
Several options are available: Battery Monitor, Multi Control Panel, Color Control GX or other GX devices, smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232).

Remote Monitoring and control
Color Control GX or other GX devices. Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge.

Remote configuring
When connected to the Ethernet, systems with a Color Control GX or other GX device can be accessed and settings can be changed remotely.

Add to cart
Victron Energy Quattro 48/5000/70-100/100 120V VE.Bus
Close

Victron Energy Quattro 48/5000/70-100/100 120V VE.Bus

$3,380.33

Victron Energy QUA485021100 Quattro 48/5000/70-100/100 120V VE.Bus

  • PowerControl / PowerAssist Yes
  • Integrated Transfer switch Yes
  • AC inputs (2x) Input voltage range: 90-140 VAC Input frequency: 45 – 65 Hz Power factor: 1
  • Maximum feed through current 2x 100 A

INVERTER

  • Input voltage range 38 – 66 V
  • Output (1):  Output voltage: 120 VAC ± 2% and Frequency: 60 Hz ± 0,1%
  • Cont. output power at 25°C (3) 5000 VA
  • Cont. output power at 25°C 4000 W
  • Cont. output power at 40°C 3700 W
  • Cont. output power at 65°C 3000 W
  • Peak power 10000 W
  • Maximum efficiency 95 %
  • Zero load power 35 W
  • Zero load power in AES mode 30 W
  • Zero load power in Search mode 15 W

CHARGER

  • Charge voltage ‘absorption’ (V DC) 57,6 V
  • Charge voltage ‘float’ (V DC) 55,2 V
  • Storage mode (V DC) 52,8 V
  • Charge current house battery (A) (4) 70 A
  • Charge current starter battery (A) 4 A (12V and 24V models only)
  • Battery temperature sensor Yes

GENERAL

  • Auxiliary output (5) 50 A
  • Programmable relay (6) 3x
  • Protection (2) a-g
  • VE.Bus communication port for parallel, split phase and three phase operation, remote monitoring and system integration
  • General purpose com. port 2x
  • Remote on-off Yes
  • Common Characteristics operating temp.: -40 to +65˚C, Humidity (non-condensing): max. 95%

ENCLOSURE

  • Common Characteristics: Material & Colour aluminium (blue RAL 5012) Protection category: IP 21
  • Battery-connection four M8 bolts (2 plus and 2 minus connections)
  • 230 V AC-connection Bolts M6
  • Weight (kg): 66 lb, 30 kg
  • Dimensions (hxwxd) : 17,5 x 13,0 x 9,6 inch,  444 x 328 x 240 mm

STANDARDS

  • Safety EN-IEC 60335-1, EN-IEC 60335-2-29, EN-IEC 62109-1
  • Emission, Immunity EN 55014-1, EN 55014-2, EN-IEC 61000-3-2, EN-IEC 61000-3-3, IEC 61000-6-1, IEC 61000-6-2, IEC 61000-6-3
  • Road vehicles 12V and 24V models: ECE R10-5

Two AC inputs with integrated transfer switch
The Quattro can be connected to two independent AC sources, for example, the public grid and a generator, or two generators. The Quattro will automatically connect to the active source.

Two AC Outputs
The main output has no-break functionality. The Quattro takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is life only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, like a water heater, for example, can be connected to this output.

Virtually unlimited power thanks to parallel operation
Up to 6 Quattro units can operate in parallel. Six units 48/10000/140, for example, will provide 48kW / 60kVA output power and 840 Amps charging capacity.

Three phase capability
Three units can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected to provide 144kW / 180kVA inverter power and more than 2500A charging capacity.

PowerControl – Dealing with limited generator, shoreside or grid power
The Quattro is a very powerful battery charger. It will, therefore, draw a lot of current from the generator or shore side supply (16A per 5kVA Quattro at 230VAC). A current limit can be set on each AC input. The Quattro will then take account of other AC loads and use whatever is spare for charging, thus preventing the generator or mains supply from being overloaded.

PowerAssist – Boosting shore or generator power
This feature takes the principle of PowerControl to a further dimension allowing the Quattro to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the Quattro will make sure that insufficient mains or generator power are immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.

Solar energy: AC power available even during a grid failure
The Quattro can be used in off grid as well as grid-connected PV and other alternative energy systems. Loss of mains detection software is available.

System configuring

  • In case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes
    with a DIP switch setting procedure.
  • Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System
    Configurator software.
  • Off-grid, grid interactive, and self-consumption applications, involving grid-tie inverters and/or MPPT Solar
    Chargers can be configured with Assistants (dedicated software for specific applications).

On-site Monitoring and control
Several options are available: Battery Monitor, Multi Control Panel, Color Control GX or other GX devices, smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232).

Remote Monitoring and control
Color Control GX or other GX devices. Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge.

Remote configuring
When connected to the Ethernet, systems with a Color Control GX or other GX device can be accessed and settings can be changed remotely.

Add to cart
Interface MK3-USB (VE.Bus to USB)
Close

Victron Energy Interface MK3-USB (VE.Bus to USB) Cable

$90.57

Victron MK3-USB (VE.Bus to USB) interface

Victron Energy Interface MK3-USB is a VE.Bus adapter, for connecting to a Multiplus or Quattro inverter/charger. Use this USB to connect the following products to a computer for configuration: Multi, MultiGrid, MultiPlus, MultiPlus-II, Quattro, Inverter (only models with a VE.Bus communication port), ECOmulti, EasySolar, EasyPlus. If you have a VE.Direct device, like a solar controller or battery monitor, you can use a VE.Direct to USB adapter. 

To install the MK3-USB driver on a computer without internet, first download the  MK3-USB driver using VEConfig3 and install it by selecting the menu Special -> USB Drivers. Only afterward connect it to your computer for the first time.
On computers with internet, Windows will automatically download the correct driver itself.

Add to cart
LiFePO4 Battery 25.6V 200Ah Smart
Close

Victron Energy LiFePO4 Battery 200Ah 25.6V Smart

$2,940.14

Victron Energy LiFePO4 Battery 200Ah 25.6V Smart

The Victron Energy LiFePO4 Battery 200Ah 25.6V Smart is extraordinarily high-performance batteries. It needs to be used in conjunction with the Victron BMS control system. Lithium-iron-phosphate (LiFePO4 battery or LFP) is the safest of the mainstream li-ion battery types. Check the full specifications of Victron Energy LiFePO4 Battery 200Ah 25.6V Smart below

VOLTAGE AND CAPACITY

  • Nominal voltage 25,6V
  • Nominal capacity @ 25°C* 200Ah
  • Nominal capacity @ 0°C* 160Ah
  • Nominal capacity @ -20°C* 100Ah
  • Nominal energy @ 25°C* 5120Wh

CYCLE LIFE (capacity ≥ 80% of nominal)

  • 80% DoD 2500 cycles
  • 70% DoD 3000 cycles
  • 50% DoD 5000 cycles

DISCHARGE

  • Maximum continuous discharge current 400A
  • Recommended continuous discharge current ≤200A
  • End of discharge voltage 22V

OPERATING CONDITIONS

  • Operating temperature Discharge: -20°C to +50°C,  Charge: +5°C to +50°C
  • Storage temperature -45°C to +70°C
  • Humidity (non-condensing) Max. 95%
  • Protection class IP 22

CHARGE

  • Charge voltage Between 14V/28V and 14,4V/28,8V (14,2V/28,4V recommended)
  • Float voltage 13,5V/27V
  • Maximum charge current 400A
  • Recommended charge current ≤100A

OTHER

  • Max storage time @ 25°C* 1 year
  • BMS connection Male + female cable with M8 circular connector, length 50cm
  • Power connection (threaded inserts) M8
  • Dimensions (hxwxd) mm 317 x 631 x 208
  • Weight 56kg

Why lithium-iron-phosphate?

Lithium-iron-phosphate (LiFePO4 or LFP) is the safest of the mainstream li-ion battery types. The nominal voltage of an LFP cell is 3,2V (lead-acid: 2V/cell). A 12,8V LFP battery, therefore, consists of 4 cells connected in series; and a 25,6V battery consists of 8 cells connected in series.

Rugged

Lead-acid batteries will fail prematurely due to sulfation:

• If it operates in deficit mode during long periods of time (i.e. if the battery is rarely, or never at all, fully charged).

• If it is left partially charged or worse, fully discharged (yacht or mobile home during wintertime).

LFP batteries do not need to be fully charged. Service life even slightly improves in case of partial charge instead of a full charge. This is a major advantage of LFP compared to lead-acid. Other advantages are the wide operating temperature range, excellent cycling performance, low internal resistance and high efficiency (see below). LFP is therefore the chemistry of choice for very demanding applications.

Efficient

In several applications (especially off-grid solar and/or wind), energy efficiency can be of crucial importance. The round trip energy efficiency (discharge from 100% to 0% and back to 100% charged) of the average leadacid battery is 80%. The round trip energy efficiency of a LFP battery is 92%. The charge process of lead-acid batteries becomes particularly inefficient when the 80% state of charge has been reached, resulting in efficiencies of 50% or even less in solar systems where several days of reserve energy is required (battery operating in 70% to 100% charged state). In contrast, a LFP battery will still achieve 90% efficiency under shallow discharge conditions.

Size and weight

Saves up to 70% in space Saves up to 70% in weight

Expensive?

LFP batteries are expensive when compared to lead-acid. But in demanding applications, the high initial cost will be more than compensated by longer service life, superior reliability and excellent efficiency.

Bluetooth

With Bluetooth cell voltages, temperature and alarm status can be monitored. Very useful to localize a (potential) problem, such as cell imbalance.

Add to cart
New
Victron Energy MultiPlus Compact 12-2000-80-30 230V VE.Bus - CMP122200000
Close

Victron Energy MultiPlus Compact 12/2000/80-30 230V VE.Bus

$1,535.35

Victron Energy MultiPlus Compact 12/2000/80-30 230V VE.Bus

MultiPlus 12 Volt C 12/2000/80

  • PowerContro Yes
  • PowerAssist Yes
  • Transfer switch (A) 30

INVERTER

  • Input voltage range (V DC) 9,5 – 17 V   19 – 33 V    38 – 66 V
  • Output voltage: 230 VAC ± 2%  and Frequency: 50 Hz ± 0,1% (1)
  • Cont. output power at 25°C (VA) (3) 2000
  • Cont. output power at 25°C (W) 1600
  • Cont. output power at 40°C (W) 1400
  • Cont. output power at 65°C (W) 1000
  • Peak power (W) 4000
  • Maximum efficiency (%) 93 / 94
  • Zero load power (W) 9 / 11
  • Zero load power in AES mode (W) 7 / 9
  • Zero load power in Search mode (W) 3 / 4

CHARGER

  • AC Input voltage range: 187-265 VAC, Input frequency: 45 – 65 Hz, Power factor: 1
  • Charge voltage ‘absorption’ (V DC) 14,4 / 28,8 / 57,6
  • Charge voltage ‘float’ (V DC) 13,8 / 27,6 / 55,2
  • Storage mode (V DC) 13,2 / 26,4 / 52,8
  • Charge current house battery (A) (4) 80 / 50
  • Charge current starter battery (A) 4 (12 V and 24 V models only)
  • Battery temperature sensor yes

GENERAL

  • Auxiliary output (5) n. a.
  • Programmable relay (6) Yes
  • Protection (2) a – g
  • VE.Bus communication port for parallel and three phases operation, remote monitoring and system integration
  • General purpose com. port n. a.
  • Remote on-off  Yes
  • Common Characteristics Operating temp. range: -40 to +65°C (fan assisted cooling) Humidity (non-condensing): max 95%

ENCLOSURE

  • Common Characteristics : Material & Colour aluminium (blue RAL 5012), Protection category: IP 21
  • Battery-connection M8 bolts
  • 230 V AC-connection Spring-clamp
  • Weight 12kg
  • Dimensions (hxwxd in mm) 520x255x125

STANDARDS

  • Safety: EN-IEC 60335-1, EN-IEC 60335-2-29, IEC 62109-1
  • Emission, Immunity: EN 55014-1, EN 55014-2, EN-IEC 61000-3-2, EN-IEC 61000-3-3, IEC 61000-6-1, IEC 61000-6-2, IEC 61000-6-3
  • Road vehicles: 12V and 24V models: ECE R10-4

Multi-functional
The Victron Energy MultiPlus Compact 12/2000/80-30 230V VE.Bus is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge technology and a high-speed AC transfer switch in a single compact enclosure. Models range from 800VA to 5000VA per module.

Unique PowerAssist feature
The MultiPlus will prevent overload of a limited AC source. First, battery charging will automatically be reduced when otherwise an overload would occur. The second level will boost the output of a generator or shore side supply with power taken from the battery.

Uninterrupted AC power (UPS function)
In the event of a grid failure or shore or generator power being disconnected, the inverter within the Multi is automatically activated and takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption.

Virtually unlimited power thanks to parallel operation
Up to 6 Multis can operate in parallel to achieve higher power output. Three phase or split phase operation is also possible. Please check our datasheets to see which models have paralleling, three phase and split phase capabilities.

Add to cart
LiFePO4 Battery 12,8V 200Ah - Smart
Close

Victron Energy LiFePO4 Battery 12,8V/200Ah Smart

$2,940.56

Victron Energy LiFePO4 Battery 12,8V/200Ah Smart

The Victron Energy LiFePO4 Battery 12,8V/200Ah Smart is extraordinarily high-performance batteries. It needs to be used in conjunction with the Victron BMS control system. Lithium-iron-phosphate (LiFePO4 battery or LFP) is the safest of the mainstream li-ion battery types. Check the full specifications of Victron Energy LiFePO4 Battery 12,8V/200Ah Smart below

VOLTAGE AND CAPACITY

  • Nominal voltage 12,8V
  • Nominal capacity @ 25°C* 200Ah
  • Nominal capacity @ 0°C* 160Ah
  • Nominal capacity @ -20°C* 100Ah
  • Nominal energy @ 25°C* 2560Wh

CYCLE LIFE (capacity ≥ 80% of nominal)

  • 80% DoD 2500 cycles
  • 70% DoD 3000 cycles
  • 50% DoD 5000 cycles

DISCHARGE

  • Maximum continuous discharge current 400A
  • Recommended continuous discharge current ≤200A
  • End of discharge voltage 11V

OPERATING CONDITIONS

  • Operating temperature Discharge: -20°C to +50°C,  Charge: +5°C to +50°C
  • Storage temperature -45°C to +70°C
  • Humidity (non-condensing) Max. 95%
  • Protection class IP 22

CHARGE

  • Charge voltage Between 14V/28V and 14,4V/28,8V (14,2V/28,4V recommended)
  • Float voltage 13,5V/27V
  • Maximum charge current 400A
  • Recommended charge current ≤100A

OTHER

  • Max storage time @ 25°C* 1 year
  • BMS connection Male + female cable with M8 circular connector, length 50cm
  • Power connection (threaded inserts) M10
  • Dimensions (hxwxd) mm 297 x 425 x 274
  • Weight 42kg

Why lithium-iron-phosphate?

Lithium-iron-phosphate (LiFePO4 or LFP) is the safest of the mainstream li-ion battery types. The nominal voltage of an LFP cell is 3,2V (lead-acid: 2V/cell). A 12,8V LFP battery, therefore, consists of 4 cells connected in series; and a 25,6V battery consists of 8 cells connected in series.

Rugged

Lead-acid batteries will fail prematurely due to sulfation:

• If it operates in deficit mode during long periods of time (i.e. if the battery is rarely, or never at all, fully charged).

• If it is left partially charged or worse, fully discharged (yacht or mobile home during wintertime).

LFP batteries do not need to be fully charged. Service life even slightly improves in case of partial charge instead of a full charge. This is a major advantage of LFP compared to lead-acid. Other advantages are the wide operating temperature range, excellent cycling performance, low internal resistance and high efficiency (see below). LFP is therefore the chemistry of choice for very demanding applications.

Efficient

In several applications (especially off-grid solar and/or wind), energy efficiency can be of crucial importance. The round trip energy efficiency (discharge from 100% to 0% and back to 100% charged) of the average leadacid battery is 80%. The round trip energy efficiency of a LFP battery is 92%. The charge process of lead-acid batteries becomes particularly inefficient when the 80% state of charge has been reached, resulting in efficiencies of 50% or even less in solar systems where several days of reserve energy is required (battery operating in 70% to 100% charged state). In contrast, a LFP battery will still achieve 90% efficiency under shallow discharge conditions.

Size and weight

Saves up to 70% in space Saves up to 70% in weight

Expensive?

LFP batteries are expensive when compared to lead-acid. But in demanding applications, the high initial cost will be more than compensated by longer service life, superior reliability and excellent efficiency.

Bluetooth

With Bluetooth cell voltages, temperature and alarm status can be monitored. Very useful to localize a (potential) problem, such as cell imbalance.

Add to cart
Victron Energy Smart Solar MPPT 150-100-Tr
Close

Victron Energy SmartSolar MPPT 150/100-Tr Solar Charge Controller

$1,020.02

The Victron Energy SmartSolar MPPT 150/100-Tr Solar Charge Controller gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, SmartSolar maximizes this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. SmartSolar maintains battery health, extending its life.

By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing.

Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in Bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations – even when there is no internet connection or phone signal nearby – you may be able to monitor your MPPT by Bluetooth-pairing with a LoRaWAN (long-range wide area network) device, available optionally.

By adding the SmartSolar Control Display you will be able to check the status of your Charger and battery-storage at a glance. Simply plug it into the face of your MPPT charger to provide you with real-time monitoring and set-up capabilities.

Features and Specifications:

– Ultra-fast Maximum Power Point Tracking (MPPT)
– Advanced Maximum Power Point Detection in case of partial shading conditions
– Outstanding conversion efficiency
– Flexible charge algorithm
– Internal temperature sensor
– Bluetooth Smart built-in: dongle not needed
– Programmable relay
– Optional: pluggable LCD display
– 5 year warranty

 

Add to cart
Victron Energy VE.Bus BMS
Close

Victron Energy VE.Bus BMS

$156.14

Victron Energy VE.Bus BMS

The VE.Bus BMS  Part Number: BMS300200000 ,  protects each individual cell of a Victron lithium-iron-phosphate (LiFePO4 or LFP) battery.
Each individual cell of a LiFePO4 battery must be protected against over voltage, under voltage and over temperature. Victron LiFePO4 batteries have integrated Balancing, Temperature and Voltage control (acronym: BTV) and connect to the VE.Bus BMS with two M8 circular connector cord sets. The BTVs of several batteries can be daisy chained. Please see our LiFePO4 battery documentation for details.

The Victron VE.Bus BMS will:

Shut down or disconnect loads in case of imminent cell under voltage.
Reduce charge current in case of imminent cell overvoltage or over temperature (VE.Bus products only, see below).
Shut down or disconnect battery chargers in case of imminent cell overvoltage or over temperature.

Protects 12V, 24V and 48V systems
The operating voltage range of the BMS: 9 to 70V DC.

Communicates with all VE.Bus products
It connects to a MultiPlus, Quattro or Phoenix inverter with a standard RJ45 UTP cable.

Other products, without VE.Bus can be controlled as shown below:
Load Disconnect
The Load Disconnect output is normally high and becomes free floating in case of imminent cell under voltage. Maximum current: 2A.
The Load Disconnect output can be used to control-

  • the remote on/off of a load, and/or
  • the remote on/off of an electronic load switch (Battery Protect)

Charge Disconnect
The Charge Disconnect output is normally high and becomes free floating in case of imminent cell over voltage or over temperature. Maximum current: 10mA.
The Charge Disconnect output can be used to control

  • the remote on/off of a charger and/or
  • a Cyrix-Li-Charge relay and/or
  • a Cyrix-Li-ct Battery Combiner

LED indicators

  • Enabled (blue): VE.Bus products are enabled.
  • Cell > 4V or temperature (red): charge disconnect output low because of imminent cell over voltage or over temperature.
  • Cell> 2,8V (blue): load disconnect output high.
Add to cart
LiFePO4 Battery 12,8V 300Ah - Smart
Close

Victron Energy LiFePO4 Battery 12,8V/300Ah Smart

$4,410.21

Victron Energy LiFePO4 Battery 12,8V/300Ah Smart

The Victron Energy LiFePO4 Battery 12,8V/300Ah Smart is extraordinarily high-performance batteries. It needs to be used in conjunction with the Victron BMS control system. Lithium-iron-phosphate (LiFePO4 battery or LFP) is the safest of the mainstream li-ion battery types. Check the full specifications of Victron Energy LiFePO4 Battery 12,8V/300Ah Smart below

VOLTAGE AND CAPACITY

  • Nominal voltage 12,8V
  • Nominal capacity @ 25°C* 300Ah
  • Nominal capacity @ 0°C* 240Ah
  • Nominal capacity @ -20°C* 150Ah
  • Nominal energy @ 25°C* 3840Wh

CYCLE LIFE (capacity ≥ 80% of nominal)

  • 80% DoD 2500 cycles
  • 70% DoD 3000 cycles
  • 50% DoD 5000 cycles

DISCHARGE

  • Maximum continuous discharge current 600A
  • Recommended continuous discharge current ≤300A
  • End of discharge voltage 11V

OPERATING CONDITIONS

  • Operating temperature Discharge: -20°C to +50°C,  Charge: +5°C to +50°C
  • Storage temperature -45°C to +70°C
  • Humidity (non-condensing) Max. 95%
  • Protection class IP 22

CHARGE

  • Charge voltage Between 14V/28V and 14,4V/28,8V (14,2V/28,4V recommended)
  • Float voltage 13,5V/27V
  • Maximum charge current 600A
  • Recommended charge current ≤150A

OTHER

  • Max storage time @ 25°C* 1 year
  • BMS connection Male + female cable with M8 circular connector, length 50cm
  • Power connection (threaded inserts) M10
  • Dimensions (hxwxd) mm 347 x 425 x 274
  • Weight 51kg

Why lithium-iron-phosphate?

Lithium-iron-phosphate (LiFePO4 or LFP) accumulator is the safest of the mainstream li-ion battery types. The nominal voltage of a LFP cell is 3,2V (lead-acid: 2V/cell). A 12,8V LFP battery therefore consists of 4 cells connected in series; and a 25,6V battery consists of 8 cells connected in series.

Rugged

A lead-acid fail prematurely due to sulfation:

• If it operates in deficit mode during long periods of time (i.e. if the battery is rarely, or never at all, fully charged).

• If it is left partially charged or worse, fully discharged (yacht or mobile home during wintertime).

LFP batteries do not need to be fully charged. Service life even slightly improves in case of partial charge instead of a full charge. This is a major advantage of LFP compared to lead-acid. Other advantages are the wide operating temperature range, excellent cycling performance, low internal resistance and high efficiency (see below). LFP is therefore the chemistry of choice for very demanding applications.

Efficient

In several applications (especially off-grid solar and/or wind), energy efficiency can be of crucial importance. The round trip energy efficiency (discharge from 100% to 0% and back to 100% charged) of the average leadacid battery is 80%. The round trip energy efficiency of a LFP battery is 92%. The charge process of lead-acid batteries becomes particularly inefficient when the 80% state of charge has been reached, resulting in efficiencies of 50% or even less in solar systems where several days of reserve energy is required (battery operating in 70% to 100% charged state). In contrast, a LFP battery will still achieve 90% efficiency under shallow discharge conditions.

Size and weight

Saves up to 70% in space Saves up to 70% in weight

Expensive?

LFP batteries are expensive when compared to lead-acid. But in demanding applications, the high initial cost will be more than compensated by longer service life, superior reliability and excellent efficiency.

Bluetooth

With Bluetooth cell voltages, temperature and alarm status can be monitored. Very useful to localize a (potential) problem, such as cell imbalance.

Add to cart
LiFePO4 battery 12,8V 60Ah - Smart
Close

Victron Energy LiFePO4 Battery 12,8V/60Ah Smart

$1,110.28

Victron Energy LiFePO4 Battery 12,8V/60Ah Smart

The Victron Energy LiFePO4 Battery 12,8V/60Ah Smart is extraordinarily high-performance batteries. It needs to be used in conjunction with the Victron BMS control system. Lithium-iron-phosphate (LiFePO4 battery or LFP) is the safest of the mainstream li-ion battery types. Check the full specifications of Victron Energy LiFePO4 Battery 12,8V/60Ah Smart below

VOLTAGE AND CAPACITY

  • Nominal voltage 12,8V
  • Nominal capacity @ 25°C* 60Ah
  • Nominal capacity @ 0°C* 48Ah
  • Nominal capacity @ -20°C* 30Ah
  • Nominal energy @ 25°C* 768Wh

CYCLE LIFE (capacity ≥ 80% of nominal)

  • 80% DoD 2500 cycles
  • 70% DoD 3000 cycles
  • 50% DoD 5000 cycles

DISCHARGE

  • Maximum continuous discharge current 120A
  • Recommended continuous discharge current ≤60A
  • End of discharge voltage 11V

OPERATING CONDITIONS

  • Operating temperature Discharge: -20°C to +50°C,  Charge: +5°C to +50°C
  • Storage temperature -45°C to +70°C
  • Humidity (non-condensing) Max. 95%
  • Protection class IP 22

CHARGE

  • Charge voltage Between 14V/28V and 14,4V/28,8V (14,2V/28,4V recommended)
  • Float voltage 13,5V/27V
  • Maximum charge current 120A
  • Recommended charge current ≤30A

OTHER

  • Max storage time @ 25°C* 1 year
  • BMS connection Male + female cable with M8 circular connector, length 50cm
  • Power connection (threaded inserts) M8
  • Dimensions (hxwxd) mm 240 x 285 x 132
  • Weight 12kg

Why lithium-iron-phosphate?

Lithium-iron-phosphate (LiFePO4 or LFP) is the safest of the mainstream li-ion battery types. The nominal voltage of a LFP cell is 3,2V (lead-acid: 2V/cell). A 12,8V LFP battery therefore consists of 4 cells connected in series; and a 25,6V battery consists of 8 cells connected in series.

Rugged

Lead-acid batteries will fail prematurely due to sulfation:

• If it operates in deficit mode during long periods of time (i.e. if the battery is rarely, or never at all, fully charged).

• If it is left partially charged or worse, fully discharged (yacht or mobile home during wintertime).

LFP batteries do not need to be fully charged. Service life even slightly improves in case of partial charge instead of a full charge. This is a major advantage of LFP compared to lead-acid. Other advantages are the wide operating temperature range, excellent cycling performance, low internal resistance and high efficiency (see below). LFP is therefore the chemistry of choice for very demanding applications.

Efficient

In several applications (especially off-grid solar and/or wind), energy efficiency can be of crucial importance. The round trip energy efficiency (discharge from 100% to 0% and back to 100% charged) of the average leadacid battery is 80%. The round trip energy efficiency of a LFP battery is 92%. The charge process of lead-acid batteries becomes particularly inefficient when the 80% state of charge has been reached, resulting in efficiencies of 50% or even less in solar systems where several days of reserve energy is required (battery operating in 70% to 100% charged state). In contrast, a LFP battery will still achieve 90% efficiency under shallow discharge conditions.

Size and weight

Saves up to 70% in space Saves up to 70% in weight

Expensive?

LFP batteries are expensive when compared to lead-acid. But in demanding applications, the high initial cost will be more than compensated by longer service life, superior reliability and excellent efficiency.

Bluetooth

With Bluetooth cell voltages, temperature and alarm status can be monitored. Very useful to localize a (potential) problem, such as cell imbalance.

Add to cart